Patton Electronics 2121, 2124, 2130, 2135, and 2135C
Ethernet MicroBridges (X.21, RS-232, RS-530, & V.35)
2121/DM-X/UI  2121/DM-X/48  2124/AM-X/UI  2124/AM-X/48 2130/BM-X/UI
2130/BM-X/48  2135C/CM-X/UI  2135C/CM-X/48 2135/CM/UI  2135/CM/48

Models 2121, 2124, 2130, 2135, and 2135C
Ethernet MicroBridges (X.21, RS-232, RS-530, & V.35)
Patton’s MicroBridge products are the cost-effective solution for expanding your LAN—without using a router!
 
Models 2135, 2121, 2124, & 2135C
 
  Features & Benefits
  • PPP Bridging Control Protocol (RFC 1638) with auto detection for compatibility with existing Patton Bridge Products and standard third-party equipment
  • Transparent LAN bridging enables the MicroBridge to pass such higher layer protocols as IP packets
  • Industry standard, shielded RJ-45 10Base-T connection
  • 802.3 Ethernet supported by transparent LAN bridging
  • 1 Mbyte RAM; 128 kbyte FLASH
  • Automatic learning and aging with support for up to 4,096 MAC addresses
  • Nine LEDs monitor power, LAN link, and DTE interface signals
  • Variety of WAN interfaces available (X.21, RS-232, RS-530, and V.35)
 
Overview  

The Patton Ethernet MicroBridge provides a cost-effective solution for connecting multiple local or remote network segments. The Patton MicroBridges feature a wide variety of serial interfaces to make your WAN connections easy. All models are equipped with an 802.3 10Base-T Ethernet RJ-45 jack, which allows a direct connection to your network equipment.

The Ethernet MicroBridge works on the MAC-layer addresses and operates independent of higher layer protocols. This functionality allows Patton Ethernet Microbridge’s to pass higher-layer broadcast, multicast, unicast, and data frames over the WAN with minimal to no configuration by the end-user. The MicroBridges are PPP ready supporting standards based layer-2 protocol interfacing. The MicroBridges are fully compatible with each other as well as Patton’s full line of bridging products. Using PPP, the MicroBridges have the flexibility to be used in conjunction with all other third part PPP compliant equipment.

Whether you are looking to add additional LANs, increase the efficiency of your WAN connection, or extending your router’s interface, Patton’s Ethernet MicroBridge is the most simple and cost effective solution around!

 

Applications


ISP Extension
The Ethernet MicroBridge Series can be used to connect a remote site LAN to an ISP POP over private or leased lines using CSU/DSUs. The Remote MicroBridge serial interface connects to any CSU/DSU for data transport over the WAN. At the ISP POP, another CSU/DSU connects to the serial port of a router, which in turn provides access to the central LAN. The MicroBridge communicates with the router using PPP half-bridging. Placing the Microbridge in the remote site saves the ISP equipment, configuration, and maintenance costs associated with a router. A MicroBridge cannot replace a router in the ISP POP because in this application a router is required due to the multiple LANS that would be attached to the ISP POPs router.

ISP Extension applications diagram
 

LAN-to-LAN Bridging
Ethernet MicroBridges can also be used to connect to the NTU’s serial port for data transport over the campus or wide area network to access another LAN. In the application diagram below the Ethernet MicroBridges (Model 2121) establish a proprietary HDLC communications link. Only packets having addresses outside each LAN are forwarded to the other.

 

LAN-to-LAN Bridging applications diagram


 
Ordering Information
2121/DM-X/UI

 
Ethernet MicroBridge, X.21 DTE with DB-15 Male, Serial Cable, 100-250 VAC
2121/DM-X/48 Ethernet MicroBridge, X.21 DTE with DB-15 Male, Serial Cable, -48VDC
2124/AM-X/UI Ethernet MicroBridge, V.24 DTE with DB-25 Male, Serial Cable, 100-250 VAC
2124/AM-X/48 Ethernet MicroBridge, V.24 DTE with DB-25 Male, Serial Cable, -48VDC
2130/BM-X/UI Ethernet MicroBridge, EIA-530 DTE with DB-25 Male, Serial Cable, 100-250 VAC
2130/BM-X/48 Ethernet MicroBridge, EIA-530 DTE with DB-25 Male, Serial Cable, -48VDC
2135C/CM-X/UI Ethernet MicroBridge, V.35 DTE with M/34 Male, Serial Cable, 100-250 VAC
2135C/CM-X/48 Ethernet MicroBridge, V.35 DTE with M/34 Male, Serial Cable, -48VDC
2135/CM/UI Ethernet MicroBridge, V.35 DTE with M/34 Male (No Serial Cable), 100-250 VAC
2135/CM/48 Ethernet MicroBridge, V.35 DTE with M/34 Male (No Serial Cable), -48VDC
NOTE:
X= “L” 6-foot (182.88cm) Serial Cable or “S” 6-inch (15.24cm) Serial Cable. Example: 2121/DM-S/UI Ethernet MicroBridge, X.21 DTE w/DB-15 Male, 6” (15.24cm) Serial Cable, UI
 

 
Specifications


DTE Interface: X.21, V.35, RS-232, or RS-530
Network Interface: IEEE 802.3 10Base-T (RJ-45)
Transmission: Synchronous up to 10 Mbps
Protocol: PPP (RFC 1661) with Bridging Control Protocol (RFC 1638)
Memory: 1MB RAM, 128KB FLASH memory
MAC Address Table Size: 4096 entries
MAC Address Aging: MAC addresses deleted after eight minutes inactivity
LEDs LAN Side: (1) yellow, general status; (1) green, link integrity
LEDs DTE Side: TXD, RXD and Power, (green); CTRL, IND and CLK, (yellow)
Power Supply Input: 100-240VAC, 50-60Hz, 0.4A; or optional -48 VDC
Power Consumption: 500mA 5VDC
Temperature: 32 to 122°F (0 to 50°C)
Altitude: 0–15,000 feet (0–4,572 meters)
Humidity: Up to 90% R.H., non-condensing
Dimensions: 3.5 L X 2.1 W X 0.78 H inch (9.0 L X 5.3 W X 2.0 H cm)
Weight: 0.72 lbs (0.32 kg)
Compliance: FCC Part 15A; CE Mark per EEC Directive: 89/336/EEC; Low Voltage Directive: 73/23/EEC

 

Patton Electronics Products