DCB MULTIPLEXERS
DCB SR-04W Wireless Multiplexer
Low cost 4 port multiplexer, wireless link to 15 miles, 57.6
Kbps ports
DCB SR-04
Low Cost Multiplexer Low
cost 4 port multiplexer, 128Kbps composite, 57.6Kbps ports
DCB SPL
Multiplexer 2 to
14 ports, DDS, Multi-point DDS, Dial-up, or ISDN composite Stat Mux
dcb sR
Multiplexer 1 to
32 ports, Frame Relay, multi-point Frame Relay, DDS, Dial-up, or ISDN composite
Stat Mux
DCB SPL Hub 2 to 10 port
hub allows multiple multiplexers to co-exist on a single composite line
dcb sr data concentrator
8
to 32 port data concentrator, Simplex or Duplex, Suitable for satellite
operation
DCB
Data
Broadcast Switch 8
to 32 port RS-232 data broadcast unit with reverse channels, Ideal for SCADA,
paging, and machine control
dcb spl144 modem / multiplexer SPL
multiplexer with built-in dial-up or leased-line modem
DCB SRX/SPL
Multi-Drop Multiplexer Firmware Firmware
to use the SR and SPL on multi-drop DDS lines or radios
DCB
SCADA PRODUCTS
|
DCB Ethernet Based SCADA Products |
|
||
|
|
|
||
DCB |
EMB-02 |
|
The EtherModbus EMB-02 Modbus/TCP to Serial Modbus gateway is a two port ethernet Modbus/TCP to Modbus RTU or Modbus ASCII gateway or converter. DIN rail mounting, two serial ports, 10/100BaseT, various power supplies. Use it to extend the life of your old RTUs when converting to Modbus/TCP or to allow multi-drop serial RTUs behind a single LAN connection. |
|
|
|
|
||
DCB |
EDNP-3 |
|
The EtherDNP3 EDNP3 DNP-3/TCP or DNP-3/UDP to Serial DNP-3 gateway is a two port ethernet DNP-3 to serial DNP-3 gateway or converter. DIN rail mounting, two serial ports, 10/100BaseT, various power supplies. Use it to extend the life of your old RTUs when converting to ethernet or to allow multi-drop serial RTUs behind a single LAN connection. |
|
|
|
|
|
|
DCB |
EPL-01 |
|
The EtherPoll is a SCADA communications serial server that allows multi-drop devices to use Ethernet LAN's. The EtherPoll connects any async serial device through a LAN and between LAN's via routers. The EtherPoll is designed specifically to support asynchronous polling protocols, such as Poll Select, Modbus, DNP, etc. |
|
|
|
|
||
DCB |
EGD-01 |
|
The Ethergate is a SCADA communications serial server that allows multi-drop DNP-3 devices to use Ethernet LAN's. The EtherGate connects async serial devices running SCADA protocols through a LAN and between LAN's via routers. Since the EtherGate is protocol aware, it uses the Ethernet much more efficiently than TCP/IP based serial servers. This makes it ideal for bandwidth limited applications. |
|
|
|
|
||
DCB |
EtherPath SS-1 Single Port Ethernet |
|
A single port ethernet serial server with the ability to have a "nailed" ethernet connection to a second unit. User can also telnet to this device to access its RS-232 or RS-485 port. |
|
|
|
|
||
DCB |
EtherPathX4 Four Port Ethernet |
|
A four port ethernet serial server with the ability to have a "nailed" ethernet connection to other units. User can also telnet to this device to access its RS-232/.485 ports. Ideal way to add remote serial devices to an ethernet LAN. |
|
|
|
|
||
DCB |
ESB-01 |
|
The EtherSeries Bridge is a small, simple Ethernet WAN bridge. It connects two LAN together via asynchronous links provided by satellite, radio, modem, or other connections. No configuration required, but with Advanced Management, it allows management via Web Browser or Telnet, and supports SNMP. Low Cost and operates at speeds from 300 bps up to 230 Kbps. Also available in a multi-point version. |
|
|
|
|
||
DCB |
IP-6600 High Performance |
|
The IP-6600 is an industrial rated router featuring two Ethernet LAN ports and either two serial ports or one serial port and a V.92 modem. The IP-6600 works well with DSL, cable or dial modems, leased line modems, CDPD or GSM modems, wireless links, satellite modems, the DCB DA-56 DSU, other WAN technologies, or even simple line drivers. It is full featured and includes a unique fall-back routing option that is ideal for mobile applications. |
|
|
|
|||
DCB |
Frame Relay Broadcast Polling FRAD |
|
A FRAD that allows async multipoint polling over frame relay networks without knowledge of the underlying protocols. |
|
|
|
|
||
DCB |
Broadcast Polling FRAD with Auto-Backup |
|
A FRAD that allows async multipoint polling over frame relay networks without knowledge of the underlying protocols. This version of the above product is designed for an automatic fail-safe backup auto-dial data path in the event the frame relay network fails. |
|
|
|
|
||
DCB |
Conitel Protocol FRAD |
|
A FRAD that enables 32 bit Conitel or Racal Redac to be used over modern frame relay networks. |
|
|
|
|
||
|
|
|
||
DCB |
WSS-SR1-W |
|
A wireless data communications system used to collect data from up to 96 remote factory floor devices. It then delivers that data error-free to a host computer over a single RS-232 port. Since the WSS-SR-1W is wireless, it eliminates the need to wire data collection stations back to the central data collection point. |
|
|
|
|
||
DCB |
DCB Wireless Modems |
|
900 Mhz and 2.4 Ghz License-Free Wireless links 115 Kbps, 20
Mile Range or greater with appropriate antennas |
|
|
|
|
||
|
|
Other Asynchronous DCB SCADA Products |
||
|
|
|
|
|
DCB |
SCADA Multi-Drop Multiplexer |
|
Allows two to four SCADA polling systems to share a single multi-drop communications network. Used with SMD devices at each remote site, as many as four completely independant SCADA systems may share the network without interference. Speed, parity and other parameters may be set individually for each port. |
|
|
|
|
||
DCB |
Conitel Protocol Converter |
|
Converts that old 32 bit Conitel or Racal REDAC protocol to allow transport over asynchronous 8-bit communications devices. Often used with our EtherPoll ethernet gateway to transport Conitel via ethernet. Special firmware is also available that transports 11 bit words. |
|
|
|
|
||
DCB |
MSU-6 Modem Port Sharing Unit |
|
An active six port modem sharing unit that works equally well with synchronous or asynchronous data ports. |
|
|
|
|
||
DCB |
Async Sharing Unit |
|
4 to 32 port RS-232 Asynchronous data sharing unit, Shares data from one port to up to 32 ports, combines data coming the reverse direction. Ideal for POS devices, SCADA, paging, and machine control. |
|
DCB T1, E1, DS-1, DSX, DS3, T3, E3, OC3 Products
|
|
|
|
DCB |
100BaseT to DS3 / E3 Converter |
|
A high speed Ethernet access unit. Transport 100BaseT full duplex Ethernet using a DS3 or E3 WAN connection. Inexpensive way to transport Ethernet via the public high speed network. Supports VLAN transparency, MPLS, ISL, and alarming. |
|
|
|
|
DCB |
100BaseT to
4X E1 |
|
Inverse E1 multiplexer for Ethernet transport. Transport 100BaseT full duplex Ethernet using up to four E1 lines. Inexpensive way to transport Ethernet by inverse multiplexing multiple E1 lines. Supports VLAN transparency, MPLS, ISL, and alarming. |
|
|
|
|
DCB |
E-1 Extender |
|
A genuine E1 repeater / extender. No setup, no software; just extends the E1 demarc with reliability and low cost. For T1, see the T-Extender below. |
|
|
|
|
DCB |
T-1 Extender |
|
A genuine T1 repeater. No setup, no software; just extends the T1 demarc with reliability at low cost. |
|
|
|
|
DCB |
DCB-AM-3440 Access DCS Mux |
|
Access Multiplexer, equivalent to multiple T1/E1 channel banks rolled into a single chassis. Supports 4 or more T1/E1 interfaces. Supports ATM/Frame Relay. Has 12 DTE slots for FXS, FXO, E&M, serial DTE interfaces, IDSL, HDSL. SNMP GUI, telnet or serial configuration, and cross connect at the DS0 level. |
|
|
|
|
DCB |
Loop V-4100 Multiservice Access Platform |
|
Used with STM-1 and DS-3 networks, ring or linear, the Loop-V 4100 provides full STM-1 access, OC-3 access, and OC-3 Add-drop. The Loop-V 4100 has full DS0 cross-connect built inside. OC-3, STM-1, DS-3, and sub-rate interfaces make this a full-featured access device that can handle 63 E1 or 84 T1 interfaces. |
|
|
|
|
DCB |
Loop 4200 IAC & DACS |
|
NEBS Certified Integrated Access Device Multiplexer, DACS, and E1/T1 converter. Has 9 or 28 slot main unit for T1, E1, DS-1, OC-3, V.35, EIA530, RS232, FXS, FXO, Ethernet, ATM, Frame Relay,DSX, or OCUDP/DS-0 interface cards. SNMP, AC or redundant DC power supplies. This is often used as a T1 channel bank replacement. |
|
|
|
|
DCB |
Loop 4300 Mini-DACS |
|
A genuine "mini" DACS and E1/T1 converter, 2 to 4 T1(E1) interfaces, any port/time-slot to any port/time-slot mapping. |
|
|
|
|
DCB |
Loop-AM 3400 T1/E1 Quad Mux |
|
Full-featured Quad T1/E1 Mux and DACs with up to 4 T1/E1 WAN or ATM ports, 12 DTE slots that accept cards having 6&10 channel U, 12 channel E&M, 12 channel FXS or FXO, Dual-slot DTE, 6 channel V.35, 5 channel RS-232 (& subrate), MDSL, with SNMP GUI, etc. |
|
|
|
|
DCB |
Loop-T2500 Fractional T-1 Speed DSU/CSU |
|
Basic to full-featured T1 DSUs with 1 port, 64 or 56XN |
|
|
|
|
DCB |
FT Fractional T-1 Speed DSU/CSU |
|
Basic to full-featured T1 DSUs with 2 to 4 ports, SNMP, Drop & Insert, 64 or 56XN |
|
|
|
|
DCB |
TM-24 Channel Bank |
|
T1 Channel bank and access multiplexer. |
DCB REMOTE ACCESS PRODUCTS
|
|
|
|
DCB |
RS-232 Access Switch |
|
4 to 152 ports of remote access, supports RS-232 and remote power control |
|
|
|
|
DCB |
APS Remote Power Access Switch |
|
Remote AC power control module for use with the Access Switch |
|
|
|
|
DCB |
RS-232 Universal Switch |
|
Any port -to- any port version of remote access, like a RS-232 PBX system. |
|
|
|
|
DCB |
EtherPath SS-1 Single Port Ethernet RS-232 Server |
|
Pipe RS-232 connections through an ethernet LAN/WAN, or connected to the Access Switch via Ethernet |
|
|
|
|
DCB |
EtherPathX4
Four Port Ethernet |
|
A four port ethernet serial server with the ability to have a "nailed" ethernet connection to other units. User can also telnet to this device to access its RS-232/.485 ports. Ideal way to add remote serial devices to an ethernet LAN. |
|
|
|
|
DCB |
SR Data Concentrator |
|
8 to 32 port data concentrator, Simplex or Duplex, Suitable for satellite operation |
|
|
|
|
DCB |
Data Broadcast Switch |
|
8 to 32 port RS-232 data broadcast unit with reverse channels, Ideal for SCADA, paging, and machine control. |
LAN PRODUCTS
Routers and Bridges
DCB |
ESB-01 |
The EtherSeries Bridge is a small, simple Ethernet WAN bridge. It connects two LAN together via asynchronous links provided by satellite, radio, modem, or other connections. No configuration required, but with Advanced Management, it allows management via Web Browser or Telnet, and supports SNMP. Low Cost and operates at speeds from 300 bps up to 230 Kbps. /td> |
|
|
|
||
DCB |
ET-6600 |
The ET-6600 bridge provides an encrypted Ethernet tunnel between two ethernet LANS. The connection between the devices may be broadband, or PPP dial-up. Industrial rated. The ET-6600 bridges all Ethernet protocols without the complexity of a full VPN install. The ET-6600 uses 128 bit AES encryption. Available in a wide varity of power supply options. |
|
|
|
||
DCB |
IP-9600 |
The IP-9600 is an industrial rated router featuring two Ethernet LAN ports two synchronous ports and two asynchronous ports. The IP-9600 supports synchronous or asynchronous PPP and Frame Relay or broadband WAN links. It is full featured and includes a unique fall-back routing option that is ideal for critical applications. Available in a wide varity of power supply options. |
|
|
|
||
DCB |
IP-6600 |
The IP-6600 is an industrial rated router featuring two Ethernet LAN ports and either two serial ports or one serial port and a V.92 modem. The IP-6600 works well with DSL, cable or dial modems, leased line modems, CDPD or GSM modems, wireless links, satellite modems, the DCB DA-56 DSU, other WAN technologies, or even simple line drivers. It is full featured and includes a unique fall-back routing option that is ideal for mobile applications. |
|
|
|
||
DCB |
100BaseT to DS3 / E3 Converter |
A high speed Ethernet access unit. Transport 100BaseT full duplex Ethernet using a DS3 or E3 WAN connection. Inexpensive way to transport high speed Ethernet via the public high speed network. Supports VLAN transparency, MPLS, ISL, and alarming. |
|
|
|
||
|
OTHER LAN PRODUCTS |
||
DCB |
HSW-08 |
An industrial rated, hardened ethernet switch. The HSW-08 is an eight port switch that features multiple power supply options , auto speed sensing, and auto MDI/MDI-X sensing. Also handles VLAN packets. Compact, stand-alone, DIN-rail, or rack mounting. |
|
|
|
||
DCB |
EPL-01 |
The EtherPoll is a SCADA communications serial server that allows multi-drop devices to use Ethernet LAN's. The EtherPoll connects any async serial device through a LAN and between LAN's via routers. The EtherPoll is designed specifically to support asynchronous polling protocols, such as Poll Select, Modbus, DNP, etc. but is also used for non-protocol asynchronous data transfers... even broadcasting data to up to 32 remote units. |
|
|
|
||
DCB |
EtherPath SS-1 Single Port Ethernet RS-232 Server |
A single port ethernet serial server with the ability to have a "nailed" ethernet connection to a second unit. User can also telnet to this device to access its RS-232 port. This full featured device responds to AT dial commands similar to dial-up modems and is quite flexible. Configure with its web browser based configuration screens, telnet, or direct connection to a terminal. |
|
|
|
||
DCB |
EtherPathX4
Four Port Ethernet |
A four port ethernet serial server with the ability to have a "nailed" ethernet connection to other units. User can also telnet to this device to access its RS-232/.485 ports. Ideal way to add remote serial devices to an ethernet LAN. |
|
|
|
DCB Wireless WAN (Building - to - Building) Serial Data Links
|
|
|
|
DCB |
DCB Wireless Modems |
|
900 Mhz and 2.4 Ghz License-Free Wireless links 115 Kbps, 20 Mile Range or
greater with appropriate antennas |
|
|
|
|
DCB |
WSS-SR1-W |
|
A wireless data communications system used to collect data from up to 96 remote factory floor devices. It then delivers that data error-free to a host computer over a single RS-232 port. Since the WSS-SR-1W is wireless, it eliminates the need to wire data collection stations back to the central data collection point. |
|
|
|
|
DCB |
SR-04W |
|
|