|
Data
Connect ( formerly Telenetics )
MIU-PowerPort
- VDC power
12 Volt DC
Power Modem with sleep modem
When not on
line, the dial up modem automatically go into a power
down mode and
consumes only 5m amps while inactive.
|
|
- Bell 202, Bell 103 & 212,
V.22bis, V.32bis, V.34
- Dial-Up and Leased Lines
- Powered from
5-16VDC
through the Data Port or an External Jack
- Automatic "Power
Down" when inactive
- -40oC
to +85oC
Operating Temp.
- Hayes™ AT Compatible
- Ideal for
Meters, Relays, RTUs, Controllers, etc.
|
Data
Connect ( formerly Telenetics )
has designed modems that work
in "remote" remote sites with very low failure rates. These devices
work where other modems roll over and die. When a service call to a remote site
can mean an all day trip these modems are the ideal solution.
The MIU/PowerPort is an industrial grade modem that can be
powered directly through the RS232 (DB25) data interface port or power jack.
MIU/PowerPort can be powered by delivering +5VDC
(regulated) through pin 10 of the DB25. An optional 12VDC version is also
available. Alternatively, an external jack allows the MIU/PowerPort to be
powered from a wall transformer or other low voltage AC or DC power source.
When not on line, the dial
up MIU/PowerPort modems automatically go into a power
down mode and consumes only 5m amps
while inactive.
The MIU/PowerPort is available with various
modulations, including...
- Bell
202T (1200bps)
- V.22bis (2400bps)
- V.32bis (14,400bps)
- V.34 (28,800bps)
...and operates over dial-up and 2
or 4-wire
leased lines at full or half duplex as appropriate.
The MIU/PowerPort has a sister product, the MIU/PowerPack,
which is powered from an internal, rechargeable Ni-Cad battery. The battery
draws its charging current from the DTE’s RS232 interface or an optional solar
panel. For more information, ask for the MIU/PowerPack brochure and
specifications.
The MIU/PowerPort is fully Hayes AT
command set compatible with programmable S-registers.
All models will operate in temperatures from -40
to 85oC and are surge protected on the analog line up to 5kV.
| Technical
Specifications
|
MIU/PowerPort
202T xx
|
MIU/PowerPort
2.4
|
MIU/PowerPort
9.6
& 9.6L
|
MIU/PowerPort
14.4
& 14.4L
|
MIU/PowerPort
28.8
|
| Modem
Line Speeds:
Asynchronous
|
0 - 1200bps
|
2400, 1200, 300bps
|
2400, 1200, 300bps
|
14400, 9600, 4800, 2400,
1200, 300bps
|
28800, 14400, 9600, 4800,
2400, 1200, 300bps
|
| DTE
Rates above modem line speeds (ie; with data compression) |
-
|
-
|
19200, 9600, 4800bps
|
57.6, 38.4,
19.2kbps
|
115.2, 57.6,
38.4kbps
|
| Protocols |
Bell 202
|
V.22bis, V.22
Bell 212A
Bell 103
|
V.22bis, V.22
Bell 212A
Bell 103
|
V.32bis, V.32 V.22bis,
V.22 Bell212A, Bell103
|
V.34, V.32bis, V.32
V.22bis, V.22
Bell212A, Bell103
|
| Dial
Up |
No
|
Yes
|
Yes (Model 9.6)
|
Yes (Model 14.4)
|
Yes
|
| 2
Wire Leased Line |
Yes1
|
No
|
Yes (Model 9.6L2)
|
Yes (Model 14.4L2)
|
No
|
| 4
Wire Leased Line |
Yes1
|
No
|
Yes (Model 9.6L2)
|
Yes (Model 14.4L2)
|
No
|
| Compatibility |
n/a
|
Hayes™ Extended AT
Command Set
|
Error
Correction/
Data Compression |
None
|
None
|
MNP 2, 4, 5 & 10
V.42, V.42bis
|
| Power
Requirements |
+5 VDC ±5% in through Pin
10 on the DB25 Data Port
(Option: 7-16VDC in through Pin 10 on the DB25 Data Port. Please
specify)
The modem can also be powered from 6-9VAC or 7-16VDC to an external
2.1mm jack.
(Optional 120VAC wall transformer available from Data Connect ( formerly
Telenetics ))
|
| Current
Consumption |
128mA @ +5VDC
71mA @ 12VDC
|
64mA @ +5VDC
35mA @ 12VDC
|
100mA @ +5VDC
56mA @ 12VDC
|
219mA @ +5VDC
123mA @ 12VDC
|
287mA @ +5VDC
160mA @ 12VDC
|
| Sleep
Mode |
Dial up modems
can be factory set to automatically fall into "Power Down"
mode
after 45 seconds of inactivity. Draws
5mA in power down mode.
Powers back up on receipt of DTR signal or incoming call.
* 202T and lease line
modems do not have this option
|
| Digital
Port |
RS232 with DB25 Female
Connector
|
| Analog
Port |
RJ11
|
| Surge
Protection
(Analog Port)
|
3.75kVac
|
5kVac
|
5kVac
|
3.75kVac
|
3.75kVac
|
| Environment |
-40oC to +85oC,
0 to 95% humidity (non-condensing)
|
| Case
Size |
5-3/8" x 4" x
1-3/8"
|
| Certifications |
FCC Part 68 Class A,
Industry Canada Certified
|
Important notes regarding leased line operation:
1 Bell202T is half or full duplex, suitable for point-to-point and
multipoint applications. 2 The standard 9.6L & 14.4L models are
4-wire, full or half duplex, point-to-point only. 2-wire, full duplex,
point-to-point available on special order.
|
