|
FEATURES
Modular integrated access device (IAD) for providing
bundled services (telephony and Internet access) over E1/T1 lines
E1/T1 access over copper, SHDSL (E1 only) or fibre
One or two independent Ethernet ports
Optional integrated four-port switch
One or two expansion slots
IP/IPX routing and transparent bridging
Support for Frame Relay (RFC 1490) and PPP protocols
OSPF support
Solid Firewall. protection
Data interfaces: V.35, RS-530, V.36/RS-449, V.24, X.21 at selectable sync
data rates: n x 56 kbps, n x 64 kbps
Selectable sync data rates: n x 56 kbps, n x 64 kbps
Fail-safe sub-E1/T1 port ensures uninterrupted service
Operates with RAD.s DXC multiservice access node for multilink star
configuration
Optional hub/switch module, up to ten ports
E1/T1 grooming of up to three fractional E1/T1 lines
Supports up to 12 analog channels (FXS, FXO, E&M)
Optional serial transparent data port
Optional dial-up or integrated ISDN backup
SNMP, Telnet or control port management
SPECIFICATIONS
The FCD-IPM is an E1/T1 or fractional
E1/T1 modular integrated access device (IAD) with a built-in router. The
FCD-IPM enables service providers to bundle data and voice services and
Internet access over a single E1 or T1 line.
The modular design enables carriers to
adopt and comply with changing customer needs. The modules include:- four or
eight analog voice ports- one or two fractional E1/T1 ports- universal data
port- 4-port hub/switch module The FCD-IPM is available with a software-
selectable internal line termination unit (LTU), and allows direct
connection to the E1 network or connection via an external LTU.
A built-in CSU/DSU allows direct
connection to a T1 network. The integrated router supports:- IP and IPX
routing and transparent bridging- backup router link capability- quick setup
and configuration- Solid Firewall (session-based) protection- NAT and Single
IP address translation- PAP/CHAP security- OSPF. The FCD-IPM can also
be used as a rate and interface converter or as an integrating multiplexer
for fractional E1/T1 analog voice and data services. Optionally, the FCD-IPM
can support a built-in SHDSL modem, eliminating the need for an external
modem.
The FCD-IPM can operate with RAD.s
modular DXC multiservice access node products for multilink star
applications, including access to SDH networks. The DXCs and FCD-IPM operate
under centralized SNMP network management. Timeslot assignment is
programmable, allowing data from the LAN, sub-E1/T1 port, analog voice ports
and data port to be placed into timeslots, either consecutively or
alternately. The FCD-IPM also allows flexible timeslot allocation of the
data port timeslots. Each timeslot of the sub-E1/T1 port is placed on the
same timeslot of the main E1/T1 link.Data from the data port can be either
assigned transparently to the main link timeslots or routed together with
the LAN data.
Immunity to hardware and power failures
is provided by bypassing the sub-E1/T1 port to the main E1/T1 link, ensuring
uninterrupted service to the sub-E1/T1 port. The E1 interface meets all
requirements of ITU recommendations G.703, G.704, G.706 and G.732.The T1
interface is compatible with virtually all carrier-provided T1 services.
Setup, control and monitoring of status and diagnostic information can be
activated in three ways:- ASCII terminal connected to the async control
port- SNMP management- in-band management through a dedicated timeslot.
The FCD-IPM supports an internal SNMP
agent and can be controlled by any generic SNMP station or by the RADview
SNMP network management application. The FCD-IPM supports dial-in, which can
be used for remote out-of-band configuration and monitoring. Maintenance
capabilities include user-activated local and remote loopbacks. The FCD-IPM
is available as a standalone unit for the desktop or a 19" rack shelf.
ORDERING
FCD-IPM-M/VC4/FXS
FCD-IPM-M/VC8/E&M
FCD-IPM-M/VC8/E&M/FXS
FCD-IPM-M/VC8/FXS
.
APPLICATION
|
