- Triple the Distance--Extend T1s to over 3 miles and
E1s to almost 5 km over one pair of wires.
- Half the Wires--The T1/E1 extenders only require one
pair of wires to operate.
- Voice and Data Extension--The CopperLink-T™ T1/E1
Extenders operate in clear channel mode allowing the
transparent passing of both voice and data.
- Plug and Play--Plug them in and the link comes up in
seconds. The line interface is even polarity
insensitive, making it easier to get running.
- Line Tests--V.52 511/511E Pattern Generator with
Remote Digital Loopback (RDL); Local Analogue Loopback (LAL).
- Front Panel Status Indicators--Front Panel LED’s
provide users with quick feedback on unit operation.
Patton’s CopperLink-T™ Patton 2113 & 2115 T1/E1 Extenders
are the perfect choice for enterprises, integrators, and
service providers needing to extend T1 and E1 circuits
beyond their typical reach while conserving the number of
wire pairs used.
With the CopperLink-T™ extenders, zero configuration is
required. They operate in clear-channel mode, thereby
facilitating the transparent extension of data and voice
bearing circuits—including the F-bit on T1 circuits. The two
active pins on the RJ connector are polarity insensitive, so
you don’t even need to worry about which wire you connect on
the line interface. Simply take them out of the box, put
them on either side of the dry copper pair, connect your T1
or E1 device and the circuit will light up immediately!
The CopperLink-T™ Patton 2113 extends E1 circuits to 16,100
feet (4,900 meters, nearly 5 km), while the CopperLink-T™
Patton 2115 extends T1 circuits to more than 3.5 miles
(18,500 feet or 5,600 meters). Both Pattons require only two
wires (one pair) to extend the TDM circuits, thereby
conserving and minimizing the copper plant resources used.
For these reasons, Patton's CopperLink-T™ extenders are the
ideal solution for most popular applications such as T1/E1
backhaul from a remote site, T1/E1 relocation, T1/E1
extension across a campus or between buildings, and
last-mile TDM delivery.
- The CopperLink-T™ simplifies transparent T1/E1
extension.
- Plug-and-Play--units automatically link up when
placed on opposite sides of a dry copper wire pair.
- Units operate in clear channel mode to easily
transport voice and data (F-bit included).
- Uses only wires on the link.
- Link interface is polarity insensitive to make
connection to the twisted-pair wires easy.
- Intuitive LEDs help you quickly troubleshoot line
and circuit problems.
CopperLink-T™ Patton 2113 E1 Extender: Dual 75-Ohm
female BNC and single 120-Ohm female RJ-48C
CopperLink-T™ Patton
2115 T1 Extender:
Single female RJ-48C
Supported Line Tests: V.52 511/511E Pattern Generator
with RDL; LAL
Clocking: CO unit preset for Network Clock, CPE unit
preset for Receive Recover
Line Coding: 16-constellation TC-PAM
Line Interface: Female RJ-11 using pins 4 & 5; Two
wires (single twisted-pair)
Front Panel Indicators: Power--Solid green
indicates unit is powered up. Slow blinking indicates unit
is in POST. Fast blinking indicates unit failed POST. Dark
indicates unit does not have power.
Link--Solid green indicates end-to-end link. Flashing
indicates unit is training. Dark indicates link is down.
Frame--Solid green indicates valid framing. Flashing
indicates signal being received, but no link established.
Power Supply: External power supply options:
Universal 90–260 VAC operating from 50–60 Hz; 120 VAC/60 Hz;
240 VAC/60Hz; -48 VDC
Compliance: FCC Part 15A, CE Mark, EMC Directive
89/336/EEC, Low-Voltage Directive 73/23/EEC
Environment: Operating Temp.: 32–122°F (0–50°C)
Humidity: 5–90% non-condensing
Dimensions: 4.7 x 1.52 x 5.0 in. (10.6 x 3.9 x 12.7
cm) |
|
2113/EUI-2PK CopperLink-T, E1 EXTENDER, 2 pack
2113/L/EUI CopperLink-T E1 Extender, Local unit
2113/R/EUI CopperLink-T E1 Extender, Remote Unit
2115/EUI-2PK CopperLink-T T1 Extender, 2 pack
2115/L/EUI CopperLink-T T1 Extender, Local unit
2115/R/EUI CopperLink-T T1 Extender, Remote unit |