GDC InnovX® NetPath 24+ Ethernet Switch
Layer 2 Switch Performance

Call us for Pre-sales and discount pricing

  301-924-7400 Ext 17 or 18 for Sales Support

Introduction

The Innovx NetPath 24+ provides fast ethernet connectivity with Layer 2 features, and can be deployed as a replacement to legacy hubs or in new installations where fast, intelligent, Layer 2 ethernet switching is desired. As part of GDC’s Innovx family of products, NetPath 24+ offers versatility and reliability needed in mission-critical enterprise environments. The NetPath 24+ is shown below deployed with Innovx routers and switches.

Features and Benefits

• Twenty four RJ45 switched 10/100 Mbps ports
• Two Slots for 1000 Mbps ports (RJ45/SX/LX modulized)
• Auto-negotiation on all 10/100 Mbps ports and support user configuration 10 Mbps and 100 Mbps
• Full wire-speed switching on all ports
• Store-and-forward switching
• Automatic address learning and aging
• Provides Spanning Tree Protocol for reliable network communication
• QoS support for two-level priorities
• Granular QoS features: allows rate shaping in 6K increments on each port
• Load balancing across individual ports and groups of ports with granular QoS
• Supports port mirroring
• Supports bandwidth control.
• Flexible management via console, Web, SNMP/RMON
• Port Aggregation up to seven groups
• Firmware upgradable via web upload, TFTP download or by local file transfer.

Secure and Managed

NetPath 24+ can be monitored and managed using standard protocols, including craft, Telnet, SNMP over UDP/IP, and HTTP (web). Also supported are MIB II, Ethernet MAU MIB, Bridge MIB, IGMP MIB, and RMON groups (Statistics, History, Alarm and Event). Access to the unit is username and password-protected. Secure Mode and MAC address filtering reject access from the unwanted nodes.

Specifications

Physical & Electrical Specifications

Innovx NetPath 24+ Dimensions
Width: 440 mm
Depth: 285 mm
Height: 1 RU
Weight: 0.3.5 kg

Electrical Characteristics:
Voltage/Frequency: 100 - 240 VAC, 50/60 Hz/ 1 A maximum

Standards Compliance

IEEE 802.3 10 Base-T Ethernet
IEEE 802.3u 100 Base-TX Fast Ethernet
IEEE 802.1d Bridging
IEEE 802.1p Priority Tagging
IEEE 802.1Q Virtual LAN
IEEE 802.3x Full-duplex flow control
RFC 1573 Evolution of Interface Group
RFC 768 UDP
RFC 783 TFTP
RFC 791 IP
RFC 792 ICMP
RFC 793 TCP
RFC 826 ARP
RFC 951 BOOTP
RFC 1493 Bridge MIB
RFC 1157 SNMP
RFC 854-859 TELNET
RFC 1213 MIB-II
RFC 1350 TFTP PROTOCOL
RFC 1757 RMON
RFC 1886 HTML
RFC 2068 HTTP
RFC 1643 Ether-like

Operational Specifications

Switch Performance & Functions
A standalone ethernet switch providing 24-port connectivity
Standard IEEE 802.1D packet forwarding function
Provides non-blocking switching performance, operating at maximum packet filtering and forwarding rate for:
    10 Mbps (14880 pps)
    100 Mbps (148810 pps)
    1000 Mbps (1488100 pps)
Provides 256 port based VLANs
Supports 6K address entries
Provides 3M bits packet buffer, 2M byte Flash ROM
Uses back pressure for half-duplex operation, and IEEE 802.3x for full duplex operation.
Provides store-and-forward forwarding scheme
Supports tag-based VLAN as in IEEE 802.1Q
Provides two-level priority. Packets are prioritized according to the source port or the 802.1p priority tag
Provides Link Aggregation function. The configurations are flexible.
Consecutive combinations up to 7 groups Link Aggregation sets
Provides GMRP for configuration of multicast groups

Console Interface
One female DB9 RS-232C console interface.
TELNET console interface

Diagnostic LEDs (per port)
Link/ACT
Speed
Full Duplex/Collision

GDC Products Page

 Purchase orders accepted on General DataComm equipment

Contract Buying and Volume Discounts available !!

Please contact us @ 301-924-7400 Ext 17 or 18 for Sales