Series 950 LAN+T1
| Southwest Microwave
Series 950 LAN+T1 23GHz Microwave Radio System 10Mbps Ethernet LAN plus 1.544 Mbps T1 .5 mile (800m) to 10 miles (16km) FEATURES: The Ethernet interface of the radio system supports all 802.3 protocols and includes an AUI connection to network devices and BNC connections to the microwave unit. The T1 data interface of the radio system supports Bell Standard 100 ohm, two-wire twisted pair designed to connect to telephony and multimedia interfaces. No on-site programming is required and no additional test equipment is needed. The Series 950 LAN+T1 system provides point-to-point connections for hubs, bridges, routers and repeaters allowing full 10 Mbps Ethernet connectivity. The 950 LAN+T1 interface has been designed to connect directly to standard T1 PBX's, Channel Banks or Telecom Multiplexers without the need for additional equipment. The 950 LAN+T1 also supports full duplex Ethernet LAN operation (20 Mbps) allowing connection to full duplex devices such as Ethernet switches and adapters. Multiplexed LAN and MULTIPLE T1 access is also available for telephony and multimedia applications. The Series 950 LAN+T1 is designed for rapid installation and alignment without special tools or test equipment. Rugged, modular radio design for ease of service and field support for years of trouble free operation in harsh weather conditions. |
|
jump to related
SPECIFICATIONS
| General | |
| Frequency Range | 21.2 GHz - 23.6 GHz |
| Input Voltage | 11 - 24 VDC Range |
| Modulation | FM |
| Duplex | Full Duplex |
| T/R Separation | 1.2 GHz (Adjustable to any CCIR Rec. 637 plan) |
| System Gain | 161 db w/2ft. Antenna |
| Power Consumption | 35 W |
| Size | 26 in. diameter X 14 in. depth |
| Weight | 20 Lbs. (9 kg) |
| Mounting | Bracket attachment to 2.5 in. dia. pole |
| Emission Designator | 36M0F1D |
| FCC Identifier | CA6950 |
| Transmitter | |
| Power Output | 18 dBm Typical |
| Frequency Stability | +/-.03 % |
| Type | Gunn Diode Oscillator |
| Receiver | |
| Sensitivity (lE-6 BER) | -65 dBm |
| Type | Single Conversion |
| Noise Figure | 12 dB |
| IF Frequency | 140 MHz |
| Antenna | |
| Polarization | Vertical or Horizontal |
| Size | 24 in. (60 cm) 2 ft. 48 in. (120 cm) 4 ft. |
| Gain | 39 dBi - 2 ft. 44 dBi - 4 ft. |
| Beamwidth | 1.6 degrees (3 dB) 0.8 degrees (3 db) |
| Operating Temperature | -30C to +55C |
| Storage Temperature | -40C to +65C |
| Relative Humidity | Up to 100% |
| Wind Loading | Withstand 125 mph wind |
| Radio Interconnections | |
| Microwave Transceiver | 1 V p-p 10 Mbps Two RG-59 75 ohm BNC (female) connectors |
| Align and Power | Three position terminal strip (12 - 22 AWG) deplugable |
| LAN+T1 Multiplexer Unit | |
| Power | 110 or 220 VAC input |
| Mechanical | 1.75 in H (1RU) x 17 in W x 7 in D 5 lbs |
| Environmental | 0 to +50C Non condensing 95% |
| LAN Interconnections | AUI male (standard 15 pin D) |
| Full Duplex Ethernet | Switch selectable |
| T1 Interconnections | Six position terminal strip 100 ohm twisted pair (TX/RX) |
| Line Build-out | 0-655 feet (switch selectable) |
| Radio Interconnections | RG-59 BNC (to 950 Radio) |
| Status and Alarms | |
| Power, System Status, Telecom Status LAN Status, Bit Error Rate, Local and Remote Loop Back | |
| Options | |
| Internal Packet Generator Remote Diagnostic RS232 Port |
|


|
Wireless LAN |
| FASTWAVE 875 LAN+T1 |
| Series 950 LAN+T1 |